Flanges
Reducing flange for polyethylene (PE) stub ends
Steel reducing loose flange. Its unique design allows a large-diameter polyethylene (PE) pipe to be connected to a flanged system of a smaller nominal diameter, acting as flange and reducer in a single piece.
- 33references
- 50 – 800 mmsize range
- 22in stock
The GA05-8 reducing flange is a smart engineered solution designed to optimise joints on polyethylene (PE) pipes. Its function is to allow a large-diameter pipe to be connected directly to a valve, pump or other equipment with a flange of a smaller nominal diameter.
This innovative design eliminates the need for a separate reducing cone and standard loose flange. By integrating both functions in a single piece, it not only reduces the number of components and joints in the installation, but also saves very valuable longitudinal space.
It is the ideal solution for designing compact manifolds, chambers with limited space or pump outlets where a diameter reduction is required. Like a standard loose flange, it rotates freely for easy bolt alignment, simplifying an assembly that would otherwise be very complex.
- Material
- High-strength carbon steel.
- Type
- Reducing loose (backing) flange.
- Key function
- Connects a larger-diameter PE pipe to a flange of a smaller nominal diameter.
- Advantages
- Saves space, reduces the number of parts and joints.
- Use
- Requires a PE stub end (not included) welded to the larger-diameter pipe.
- Flange standard
- Drilling compatible with PN10/16 (to EN 1092-1).
- Surface finish
- Bare steel (protective treatment recommended).
- From PE pipe Ø62 mm to DN 50 flange
- From PE pipe Ø73-80 mm to DN 50 flange
- From PE pipe Ø73-80 mm to DN 65 flange
- From PE pipe Ø85-95 mm to DN 65 flange
- From PE pipe Ø100-110 mm to DN 80 flange
- From PE pipe Ø120-134 mm to DN 100 flange
- From PE pipe Ø135-141 mm to DN 125 flange
- From PE pipe Ø150-160 mm to DN 125 flange
- From PE pipe Ø170-181 mm to DN 150 flange
- From PE pipe Ø230-241 mm to DN 200 flange
- From PE pipe Ø284-294 mm to DN 250 flange
- From PE pipe Ø335-341 mm to DN 300 flange
Full dimensions and weights in the Technical data sheet (PDF).
- Pump outletsIdeal for connecting a pump outlet to a smaller-diameter pipe.
- ManifoldsAllows irrigation or industrial distribution manifolds to be designed and built far more compactly.
- Equipment connectionFor installing valves, filters or meters of a smaller diameter than the main line without additional parts.
- Space optimisationThe best solution for chambers, plant rooms and any installation where longitudinal space is limited.
- Standardised transitionsEfficiently reduces a PE line to a standard flange size with a single piece.
References
Reducing backing flange for HDPE stub ends
DN
PN
No references match the filters.
From the blog: guides on this family
More news
Other flanges families
View the category
GA05-1Threaded flange DIN 2527Threaded flange made of ST 37.2 carbon steel. Converts a male-threaded pipe connection into a standard flanged connection (DIN 2527 / EN 1092-1), e…
GA05-2Blind flange DIN 2527Blind flange made of ST 37.2 carbon steel for securely sealing line ends or flanged valves. Complies with the DIN 2527 (EN 1092-1) dimensional stan…
GA05-3Irrigation-type slip-on welding flangeCarbon steel slip-on welding flange, light-series irrigation type, PN 10 (DN 80 also in PN 16). The economical, widely used option for creating fla…
GA05-4Slip-on welding flange DIN 2576 / 2502Slip-on welding flange made of carbon steel. Designed to create a permanent, high-strength flanged joint on steel pipes. Complies with DIN 2576 (PN…
GA05-5Irrigation-type backing flange for HDPE stub endsIrrigation-type steel backing (loose) flange for polyethylene (HDPE) stub ends. Converts a welded PE pipe into a standard flanged connection, rotat…
GA05-6Backing flange for PVC stub endsSteel backing (loose) flange, designed specifically for use with a solvent-welded PVC stub end. Its free-rotating design allows instant bolt alignm…